What's new
  • ICMag with help from Landrace Warden and The Vault is running a NEW contest in November! You can check it here. Prizes are seeds & forum premium access. Come join in!

Stanley Blower Fan Mod

The Dopest

[THC] True Hippie Coonass
Veteran
terp182, thats the only fan in my ventilation setup. mine has been runnin 24/7 for over a year with a load on both input and out and its still quiet as the day i bought it, runnnin smoothly!

ItsGrowTime, whoever posted that didnt read. i posted the specs but as Sandman( :wave: ) mentioined, it does not take ito account the load of ducting/fittings filters etc. the fan does not bog down though, its a beast i stand by!

aeric, right on!!

A-Loc that is one of my setups now. two 400w and a filter with the fan in between. im confident you will have no porblems with ventilation issues. gl and post up!!
 

ItsGrowTime

gets some
Veteran
The Dopest said:
ItsGrowTime, whoever posted that didnt read. i posted the specs but as Sandman( :wave: ) mentioined, it does not take ito account the load of ducting/fittings filters etc. the fan does not bog down though, its a beast i stand by!

Preachin to the choir man! I love mine. Brought down plant top temps under the 600w by 5 degrees on setting 3. I covered the switch side intake with duct tape too. Whoever said it sounds like a helicopter taking off (but fairly quiet) was dead on.
 

A-Loc

mofuckin farmer smurf
thanks alot i defiantly will. i'm trying to figure out how to get my camera hooked up to my new laptop. freegin lost the cd with all the crap on it. what do you usually yield with the 2 400's?
 

EZB581

Member
How about a general idea on the amps the blower uses set at it's highest speed setting? All the manual states "a minimum No 14 AWG power chord ,do not exceed 1,875 watts". Is this info listed on the fan motor? I haven't disassembled one to that point. :chin:
 

Echoes

Member
My Stanley says 0.75A for the fan motor (located on the bottom of the blower) but I'm not sure if that's for lowest or highest setting. Either way, I can't imagine it putting out more than 1.5A max.
 
Quick question guys i went and bought my stanley blower today since a friend wanted his canfan back i was about to dish the 300 bucks thank god for this , my one problem is im still having a little bit of a heat issue to break it down real quick i have a sealed veg room about 2.5x4x6 (LXWXH) and an open veg room (its basically my closet split in two and since summer is coming ive been hitting 87-91 deggress the way i have it setup atm is i have three hole cut in my veg room two for the entrance and exit out the A/C Hood and one intake i currently have the blower sittin on top of my grow cab sucking air in from the main closet pushing it through the my 175w hood > 400 w hood > then finally going into my attic , so basically would it be better for me to just suck in the air from 175w hood and then push it it through the 400 watt and then into my attic and then used the hole i used for the Hood intake for jsut fresh air intake since it would be sucking more air out of my veg room through the hood?? sorry if this sounds confusing to break it down a little easier its currently set up like this...

--->sucking in air through blower / ----> exits blower >175 w hood > 400 hood > then into my attic

and im considering settting it up like this....

175w hood <-- suck air in from hood and veg room and push it out from the blower through my 400 watt hood and then into my attic, and add an 6 in" intake where the hole was for the entrance of the 6 inch ducting.

Sorry if this sounds confusing. its just hard to explain if your not looking at it..
 
Last edited:

EZB581

Member
how my two stanleys are installed

how my two stanleys are installed


this sits on top of a 4 by 3 by 6 cab, 6" duct is siliconed in place, works fine to cool this cab with an open 250 mh light

this one has the "Dopest oneside draw " mod
 

The Dopest

[THC] True Hippie Coonass
Veteran
EZB581 hey! on that one side modded one, is it pulling fresh air from the insulationi covered window and blowing theough the hoods? and to where does it exhaust, how many watts/hoods etc if you dont mind. btw nice job!
 

EZB581

Member
Thanks Dopest,

Yes, I left the window open a bit & covered it with r max sheeting. The blower draws from the window. pushes thru 6" duct. It's pushing air thru 3, 1K hydrofarm hoods. Then exhausts to the attic. The blower cools very well on 2 lights, the 3rd is a bit much but adequate. I can easily leave my hand on the 3rd light which is fairly warm but not hot at all. I installed the vents in these old model hydrofarm hoods and isn't the most efficient design by far.
IMHO a stanley blower could easily cool two of the newer vented 1K hoods. Cool tubes would be even better.
Dopest, here is a better pic for You

 
Last edited:
G

Guest

Can anyone who has one put together tell me how much light comes through from the lit pulling end to the other exhausted end of the duct? I don't know how much light bleeds through and I will be exhausting from my veg hut to my flower hut intake. Those 6 hours that the veg hut will be lit and the flower tent will be dark has me wondering what to expect with light bleed.
 

marley1

Member
you should be fine, i didn't notice any either from inside my closet out of the duct, or inside the closet from the duct.
 
G

Guest

marley1 said:
you should be fine, i didn't notice any either from inside my closet out of the duct, or inside the closet from the duct.


Oh man, that is a huge relief! :woohoo:
 

The Dopest

[THC] True Hippie Coonass
Veteran
hey nice job there EZB, thanks for the better pic update! here are a couple more stanleys just put into action...

this ones pullin through the single side mod from the cab and exhausting through about 12lbs of carbon in a 1" bed


and this one is in a dryin cab im building and its sucking through 40lbs of carbon in a 3" bed and exhausting out through rear of cab
 

Pink

Member
lol, my twin bro, who knew you were gonna be famous. I love my fans D. Thanks so much for all your help. Can't wait to see ya in july. :D
 

A-Loc

mofuckin farmer smurf
hmmm i wonder if this would cool my space 2 1/2ftx4ftx6ft running 2 open 400 watters?
 

ItsGrowTime

gets some
Veteran
A-Loc said:
hmmm i wonder if this would cool my space 2 1/2ftx4ftx6ft running 2 open 400 watters?

If you attached the Stanley to ducting and tapped your 400w's into it it would help a few degrees. Just having it sucking in air in the room probably won't help cool the lights much, if at all. You need the ducting to make a difference.
 
Top