rb extractors
Member
when your appions finally crap out completely, you might want to consider the reftec diablo. about the same price via century tool and much quieter
-
As of today ICMag has his own Discord server. In this Discord server you can chat, talk with eachother, listen to music, share stories and pictures...and much more. Join now and let's grow together! Join ICMag Discord here! More details in this thread here: here.
Mk III Terpenator
- Thread starter Gray Wolf
- Start date
SDgrower: What has happened is due to not having a good sized filter/dryer on the inlet most likely. What I've seen on rebuilds is small amounts of resin would build up in the piston ring groove causing it to stick in the groove. This keeps the ring from moving freely in the groove and sealing properly. Yours is probably filled with resin.
Now that the machine has cooled off and isn't running it will hold pressure perfectly since the resin is what is doing the sealing!!
Sorry dude, but a rebuild is gonna be in order if that much goop is drooling out the bottom of the cylinders...
After installing a very large filter dryer I've managed several hundred hours of run time without issues.
Last point, there are little copper shims at the bottom of the cylinders where you are seeing leakage. On rebuild they need to be installed at the same place Relative to the crankcase housing. Mark the lower crankcase with a felt pen where they came out. The cylinders might be tough to get off too, the resin will make them stick, heat them up with a heat gun.
Peace, RB
Now that the machine has cooled off and isn't running it will hold pressure perfectly since the resin is what is doing the sealing!!
Sorry dude, but a rebuild is gonna be in order if that much goop is drooling out the bottom of the cylinders...
After installing a very large filter dryer I've managed several hundred hours of run time without issues.
Last point, there are little copper shims at the bottom of the cylinders where you are seeing leakage. On rebuild they need to be installed at the same place Relative to the crankcase housing. Mark the lower crankcase with a felt pen where they came out. The cylinders might be tough to get off too, the resin will make them stick, heat them up with a heat gun.
Peace, RB
rb extractors
Member
you can still get resin in your appion even with a large filter drier if you ran liquid accidentally into your appion :/
They need to be built by buyer (if I am correct), unless someone is making them. Biggest obstacle, is obtaining n-butane in 5 gallon, can with liquid siphon.
GW slap me if I am wrong!!! Have been mesmerized by this for months, but that one problem stops me.
Someone said that Glacier was going to produce tops, pre-made, on another site, for lil terp.
Details can be found at skunkpharm. These guys are PHD's of THC!!!! I hope GW or the site, does not mind that comment.
If you, have a "LOT" of money, Tamisium has units. Entry level is 1600 for basic unit. Goes "WAY" up from there. Could buy nice used car for cost of some.
I agree it is costly, but doing oncology work I think it would be very beneficial, I would like to test the healing claims
Skunk Pharm Research sells no Terpenators, but you might ask Specialized Formulations to assemble a Mk IIIA kit for you.
That picture is an aye-aye.
Was confused, since late.
Do not know about that, but Dutch Passion is producing low THC, high CBD (4 percent THC).
Benefits of the process and price of the equipment are not synonymous. When we ran the Lil Terp longside a TE-175, performance was about equal.
Tamisium makes a purdy unit that works well, but the whole reason for the very existence of the Lil Terp, was to provide equal performance at ma and pa prices.
Having done so, I haven't pursued or further developed it, because I personally believe that the non passive recovery Terpenator is a superior system, unless you are gifted with both money and time.
Thanks GW, I'll look up the Lil Terp at the Pharm
shoot! now that i have been reading all weekend my head is spinning. So, is the terpenator/MKIII a butane extractor? I kind of doddled back and forth between CO2 and butane and did not even realize i was jumping back and forth between threads here, the pharm and other forums.
