My secret winter garden

[kasvi]

I like how you can see difference in plants already.
C99 3

C99 2

Somango

Walkabout 1

Bubblegummer 1

 

[starke]

Keep up the good work.

 

[kasvi]

Keep up the good work.

I will.

I printed light holder for case number 2. It was fragile still after calibration of extruders steps per unit.

This was printed at 185C. I will test 195C next. Maybe that will help.

I have also replaced Bubblegummer 2 with walkabout seed which went straight to soil.
Bubblegummer 2 had stopped growth before seed shell had become off. I freed it and it wilted away overnight.
I have lost all hope with Jack herer seed.

 

[kasvi]

I started following watering regime today.
1st watering:
-Silicon+ 4ml/l
-Aloe vera extract 0,3ml/l
2nd watering:
-Silicon+ 4ml/l
3rd watering
-Silicon+ 4ml/l
-Coconut water extract 1ml/l
-Aloe vera extract 0,3ml/l
4th watering:
-Silicon+ 4ml/l

 

[kasvi]

3d printer just finished light holder. It is still fragile because layers are not sticking to each other properly. I will now try to print at 205C.

 

[doams]

would it be possible to print around some metal stick and the stick will hold the whole thing together same way as they use it when building houses? like metalic skeletal thingie?

know nothing about 3d printing..just an stoner idea

 

[kasvi]

would it be possible to print around some metal stick and the stick will hold the whole thing together same way as they use it when building houses? like metalic skeletal thingie?

know nothing about 3d printing..just an stoner idea

It could work with thin enough stick. The nozzle might hit it if it is too thick.

 

[kasvi]

I printed light holder maybe 4th time. This time it did not break when bent.

I will go shopping tomorrow or day after tomorrow for black paint.
Fans has been send to me finaly.

 

[kasvi]

I finished light holder today.


Here is how my plants looks like today.

 

[kasvi]

Last two are from same seed.

 

[kasvi]

Fans arrived today.
I have not gone shopping yet. I will later today. Some time after nice cup of coffee.
I am thinking about culling smallest one and replacing it with yogurt cup challenge plant.
I think I will get more yield from 250ml coco fem af than that small one.
Walkabout 2 has surfaced.

 

[kasvi]

FUCK! I am so pissed right now. I did go and check how plants are doing and walkabout 2 wilted away. I had taken saranwrap off from top of it accidentaly when I was high. It had not grown its taproot deep enough.

Edit. I might have over reacted. After misting with water and removing it from pc case it looks ok.

 

[ice-cream]

3D print a new taproot ?

j/k sorry to hear man

 

[Jonnysact]

Great thread! Your craftsmanship is very inspiring!

And I'm raising some Cinderella's now too!!!! Ooooooo, they could be friends!

 

[kasvi]

3D print a new taproot ?

j/k sorry to hear man

lol. I might have over reacted little. I removed plant from case and misted it with water and now it looks ok.

Great thread! Your craftsmanship is very inspiring!

And I'm raising some Cinderella's now too!!!! Ooooooo, they could be friends!

Thank you!
Of course they can be friends.
Is your Cindarella from female seeds or brothers grimm?

I am going to remove cindarella 1 from pc case and replace it with 250ml coco yogurt cup plant for yogurt cup challenge. It is growing too slow.
Strain is Seedsman auto White widow. I know that it is not ideal to grow autos with 12/12 light cycle but only fem seed left in addition to AH and SSH was either auto white widow or auto northern lights.

I ordered 3 Ace tropical mix and 2 cannabiogen mix for next fall/winter. I got 3 Original Afghani #1, 3 Narkush, 13 White widow, 1 auto white widow and 5 Tikal seeds as freebie.
One out of 3 Tropical mix packs I ordered was 5 seed version instead of 10 seed I ordered. They fixed this by sending me one 10 seed tropical mix packet.
I am very pleased with Seedsman and recommend it to others. I think I will grow that 5 seed tropical mix after these plants are ready together with Bodhis gear.

One of Cindarella twins, number 2 has some kind of mutation.
You can see it in lowest leave in picture. One extra finger.

Bubblegummer 1 has yellowing in tip of two leaves.
I watered plants little bit with worm casting tea.

 

[Jonnysact]

My Cindies are from Female Seeds. They are loving life Started a thread about them in the micro grow section which you are more than welcome to check out.

Hope you're having a great weekend!

 

[kasvi]

I have bought the paint two days ago, it was 9 euros, and paited parts day before yesterday, yesterday I installed some parts. One part did break because I dried to use hammer to instal it. I will print it today again.
I also put some sealand around some parts and on top of some holes.


[FONT=Arial, Helvetica, sans-serif]
I have also ordered ona block which was 14.50€.

Things to do:

Print:
hole covers (6/7 done)
Instal:
-covers for holes (6/7 done)
-plastic for walls
-fan
-activated carbon filter
-lights

Money spent: 426,41€ [/FONT]

 

[kasvi]

Bubblegummer 1 has some kind of rust spots and yellowing on leaves.

And I noticed that Somango is also a mutant. It is missing one finger.

 

[Jonnysact]

Interesting. That's quite early to be getting calmag def (rust spots and pale leaf)

What's your medium/ph? I'm not expert, but at this point the cotyledons should be providing your plant everything it needs in terms of food, so the only thing I can think of is potentially over watering?

My C99 is from Female Seeds. She's explosive!

 

[1madtrapper]

you got ph troubles...check run off and water for ph level adjust it. Cheers


14 pages and just seedlings...really wont wait for a joint from here.