-
ICMag with help from Landrace Warden and The Vault is running a NEW contest in November! You can check it here. Prizes are seeds & forum premium access. Come join in!
Snype's Guide To Cloning In Rockwool Or Aeroponics With 100% Success Rates!
- Thread starter Snype
- Start date
where does it go?
Heh i used to use rusty, dirty old scissors and just cut a stem from the plant and stick it in the cube, unsterile as fuck, 100% success rate. Now im "operation room" sterile as fuck, use a razor blade - do everything as i should and i have had a 0% success rate for the past 5 months... fuck cloning, love growing, more than smoking even, but i loath cloning...
When you do your process , what is the ph and ppm of your solution ? Do you or did you get all the clones wilting after 3-5hrs or the next day ?
I was following a tech that was 80ppm after the mix . I think now it was incorrect info and too low of a ppm . Anyhow now I am here .
So I took two cuts , yes only 2 as a practice run and mixed up this mix of snypes which gave me 500ppm solution , I thought that was too high . 1 died off and 1 is still going after 8 days . Now I tried this again but I cut in just over half at 300ppm and took extra cuts and I am impressed . They're reaching for the light and none have wilted . I'm not looking for roots in 3 days but that would be great , I'm just looking for that success rate again ! Try this out or determine your ppm and maybe adjust them
Snypes rockwool guide
Snypes rockwool guide
In his guide it states to technaflora thrive alive but i see on sticky note in picture below shows he used superthrive. He said in other posts he preferred super thrive oner thrive alive so was surprised to see thrive alive in formula in guide.
Snypes rockwool guide
In his guide it states to technaflora thrive alive but i see on sticky note in picture below shows he used superthrive. He said in other posts he preferred super thrive oner thrive alive so was surprised to see thrive alive in formula in guide.
Came across this a few days ago..trying to step up my clone game, used to be solid, but havent been doing as well lately. I just took a batch following these directions (mostly). I did use cloning gel, I just had some around, plus it seems snypes key here is the whole moisture content thing. My cubes weighed 56-57 grams after 2 hours soak. I dont have GH stuff around so I used Technaflora, and also the root 66, and thrive alive red, phd. I didnt squeze the cubes, to drain. The one thing I have been wondering is if snype uses a heat mat ? I usually do but didnt notice anything about one in his method, so dont have the tray on one at the moment. Ive always misted daily, which Im not doing this time, as well as leaving water in the bottom of the tray, not this time.
T
TrueReligion
I wouldn't use a heat mat, the easiest way I've found to clone was clip and drop the cut stem into water replacing the water every 1-2 days it takes a little longer but a guaranteed root.
M
marygrace
In memory of Snype , wherever you are , to have helped many growers on ICMag .
Thank you so much homie !
Thank you so much homie !
Yep ! This is the shit, Been following the recipe and method exactly, and now Im getting 100 % ,,even with less than perfectly healthy cuts ! The one thing I do in addition, that I think REALLY helps , is taking the cuts a few days prior to planting. I let them "soak" in purified water for 3 -4 days, til whenever I get around to it. Thanks Snype !
frostqueen
Active member
Just a huge thank you to Snype for all he contributed here. I've been using this technique for my aerocloner for many years now and it is perfect. Success every time.
Boyd Crowder
Teem MiCr0B35
snypes on ig
Using what name?? Hundreds of variations of snype there.
