so after running 2 years is a 5x10x7 tent, I felt it necessary to upgrade my flower room. well it was a bit more than I expected....work and cost wise, but you only live once right? lol
anyways, heres a materials list and a build list
8x12x7' framed room.
2x4's for corner studs
2x3's for center studs
4x8 1/2" osb floor x3
4'x125' reactive barrier material
10x100' 6ml black poly roll
10x100' panda film (5.5ml iirc)
10 rolls of 3m flex hvac tape
8 rolls gorilla duct tape (black)
1 box 1500 staples
50ct roofing nails w/tabs (removed nails, replaced with 1" fine drywall screws) (interior lining hardware)
50ct 3" fine drywall screws framing screws
the osb floor has 3 layers of black poly for protection
the entire side walls as well as the ceiling is wrapped 2x with black poly.
the roof has an additional 2x panda film poly
the floor has an additional 2x panda film poly
every screw/staple is fully sealed (absolutely no air leaks)
all seams are 3x taped over
3x big kahuna hoods with 3x600hps
8000btu portable a/c
8" 275cfm intake fan on speed controller
MONSTER 65 pound carbon scrubber matted to an 750cfm 8" exhaust fan on speed controller
2x 6" 440 cfm fans for cooling the 3 hoods
I finally turned on the lights last night for a test run w/o plants to get an idea of things. everything seems great. just have to dial in the negative pressure, get my a/c intake speed right, move the plant in (after I feed them and stake the shit out of them). ill post a few more pics tomorrow morning of the hood exhaust, scrubber exhaust, ballast mounting, ect.
I started this build last week Monday. I only had help on Monday doing the frame work. everything else was done by myself w/no help.
anyways, heres a materials list and a build list
8x12x7' framed room.
2x4's for corner studs
2x3's for center studs
4x8 1/2" osb floor x3
4'x125' reactive barrier material
10x100' 6ml black poly roll
10x100' panda film (5.5ml iirc)
10 rolls of 3m flex hvac tape
8 rolls gorilla duct tape (black)
1 box 1500 staples
50ct roofing nails w/tabs (removed nails, replaced with 1" fine drywall screws) (interior lining hardware)
50ct 3" fine drywall screws framing screws
the osb floor has 3 layers of black poly for protection
the entire side walls as well as the ceiling is wrapped 2x with black poly.
the roof has an additional 2x panda film poly
the floor has an additional 2x panda film poly
every screw/staple is fully sealed (absolutely no air leaks)
all seams are 3x taped over
3x big kahuna hoods with 3x600hps
8000btu portable a/c
8" 275cfm intake fan on speed controller
MONSTER 65 pound carbon scrubber matted to an 750cfm 8" exhaust fan on speed controller
2x 6" 440 cfm fans for cooling the 3 hoods
I finally turned on the lights last night for a test run w/o plants to get an idea of things. everything seems great. just have to dial in the negative pressure, get my a/c intake speed right, move the plant in (after I feed them and stake the shit out of them). ill post a few more pics tomorrow morning of the hood exhaust, scrubber exhaust, ballast mounting, ect.
I started this build last week Monday. I only had help on Monday doing the frame work. everything else was done by myself w/no help.
Attachments
Last edited: